One of my first questions to ask a divocup customer is whether he is cut or uncut. But I fully realize that cut, or circumcised, comes in many degrees: loose to tight cuts. A loose cut is when flaccid, the shaft skin can, with a certain amount of shaft retraction towards the pubic bone, cover at least the ridge of the glans. If your penis skin can partially or fully cover your penis head, then these instructions are for you to add to your divocup skill set.
To put on a tight divocup with the help of 'loose' shaft skin:
1. Clean and lube the inside of your divocup
2. Holding your penis, press your glans while gripping your shaft skin, so the shaft retracts and the skin covers at least part of the head. This accumulated skin over the head should be enough to fit inside of the opening of your divocup.
3. Place the venting tube inside the divocup.
4. Place the divocup opening on and around your skin covering the glans. The venting tube should be sticking out.
5. Squeeze the shaft to force blood into the head of the penis. With the skin already in the opening, you basically want to "un-retract" the penis so the head ends up sliding into the divocup.
6. Continue to grip the penis until the divocup is completely filled and use the tip of the venting tube to get the air bubbles to escape. Once it is air-free, gently remove the tube without letting go of the pressure on your penis with the divocup. If you loosen your grip, air will enter the cup and you will need to squeeze again to get the air out.
7. The shaft will bulge out of the divocup when hanging freely on your penis. This is what you want. The spandex divosuit will compress this bulge to the diameter of the divocup.
Applying the divosuit:
1. Grab a divosuit and stretch it over the applicator. It will be really tight the first time, and the stitching will open and lay flay. This is what is supposed to happen.
2. Once the divosuit is fully on the applicator, insert your penis in the opening, making sure that the end with the rubber band is facing away from you. The rubber is there to prevent the divosuit from slipping off the far end of the applicator.
3. Slide some divosuit off the applicator and let it compress around the middle of divocup. Then insert your penis further into the applicator while laying more divosuit on your shaft. If you have folds of skin, gently stretch your skin so the spandex goes on stretched, smooth skin, so the shaft has some space to elongate. Try to avoid stretching the spandex off the applicator, instead feed it on the shaft with your fingers.
4. Once you reach the base of your penis, reverse direction and pull the applicator off your shaft, holding the divosuit around the base to allow the spandex to lay another layer as it is being removed. Layer back and forth with the applicator until all the divosuit is on the penis.
5. Top layers can be placed starting from the base of the penis, and ending halfway over the divocup.
To remove divocup for peeing:
1. Fold back the divosuits one layer at a time to expose the front half of the penis
2. Pull the divocup at an angle to break the air seal for easy removal
3. Sit on the toilet and pee. If urine pressure builds up at the base of the penis, use your hand to milk the pee through the divosuit. This is done by coordinating your "pee push" with a base squeeze with your hand. Make sure that you also hold the divosuit in place at the base of the shaft. This hand pump action will also force blood into the shaft, causing greater elongation and girth.
4. Once finished urinating, squeeze and shake the shaft, and grip the divosuit covering the shaft. Retract the shaft by pulling the divosuit forward, and accumulate the skin to cover the glans again.
5. Follow the directions above in the very first set of instructions, starting with inserting the venting tube in the divocup, then place the cup over the skin covering the head, then pressing and squeezing until the head fills the cup. Pull out excess skin from the cup and unfold the divosuits one layer at a time to its original position.
Remember, as your shaft elongates during the day (which causes the divosuited penis to curve or bend after a few hours of use), remove the divosuits and reapply them on your elongated penis. The shaft should become straightened again when fully divosuited, and more elongated than the earlier application.
On another note, all orders made while I was on vacation are almost shipped, as I now have to make much larger batches at a time and then ship them by mid week. It took extra time making the bonuses I add to each divosuit order :)
If anyone needs webcam help with their divo products, please let me know and I will be happy to assist you by appointment, free of charge.
Thanks for reading!
Ronielle Out
